ARLA/CLUSTER: Waters & Stanton anuncia o novo Apache Labs Anan 8000DLE HF & 6M 200W SDR Transceiver

[João Costa > CT1FBF]

 Waters & Stanton announce the new Apache Labs Anan 8000DLE – the Ham Radio
Transceiver of 2017

The *ANAN-8000DLE HF & 6M 200W SDR Transceiver* meets and exceeds the
requirements of even the most discerning Amateur Radio Operator, it is
based on the work of the OpenHPSDR community.

Keeping in mind the various requirements posed by new cutting edge
technologies implemented in the radio it has been designed from scratch,
the design successes of the previous generation hardware has been improved
in the new implementation.

The ANAN-8000DLE uses an entirely new redesigned transmit chain keeping in
mind PureSignal (Predistortion), the result is astounding IMD performance,
the typical transmit IMD distortion is about a 1000 times lower than that
achieved by a typical modern transceiver available today. It is the world’s
first Amateur Radio transceiver to use a 50v LDMOS device in the finals.

The ANAN-8000DLE includes two phase synchronous front ends to enable
Diversity reception,

An internal four phase low noise boost supply is used to convert 13.8v to
50v for the finals, this enables the user to have the flexibility of using
industry standard 13.8v DC as well as battery power whilst at the same time
the radio provides all the advantages of the 50v LDMOS amplifier.

The front panel Display is microprocessor driven and displays all critical
parameters such as Forward and Reflected Power, SWR, Current, Voltage,
Temperature. The microprocessor also provides real time protection for all
these parameters.

For more information, specification and to order
http://hamradiostore.co.uk/anan-8000dle.html

* Specifications:*

General Specifications:

   - Architecture: Direct Sampling DDC/DUC Transceiver
   - Phase Noise (Clock): -149dB @ 10Khz
   - Interface: Ethernet
   - TCXO Stability (Typical): /- .1 PPM
   - Modes: CW, SSB, NFM, AM, Digital
   - Frequency Resolution: 1 Hz
   - Antenna Ports: Three SO-239 50 ohms Software Configurable Ports, One
   BNC for RX2



Mechanical Specifications:

   - 12Kg (approx. Weight)
   - Dimensions: 483MM (L)  x 123MM (H) x  320MM (D) (Not including
   extrusions)
   - Stainless Steel Chassis and Aluminum Heatsink



Electrical Specifications:

   - 13.8v DC @ 35A, 3A Receive/35A Transmit

Receiver Specifications:

   - Receiver Architecture: Direct Down Conversion
   - Dual 16 bit Phase Synchronous ADCs
   - Independent filter banks for each ADC
   - 10/6M LNAs
   - Frequency Coverage: 9Khz to 60Mhz
   - Attenuator: 1-30dB step attenuator
   - Reciprocal Mixing Dynamic Range (RMDR): 116dB @ 2Khz
   - Receiver Phase noise: -149dB @ 10Khz
   - Image rejection: 100dB
   - Hardware support for 7 independent receivers assignable to either ADC



Transmitter Specifications:

   - Transmitter Architecture: Direct Up Conversion
   - DAC Resolution: 16 bit
   - RF Output Power: 1-200W SSB, CW, FM, RTTY, Digital; 1-50W AM
   - IMD: IMD3 typically -72dB @ 200W output on 20M
   - Harmonics: Typically better than -50dBc on HF and -60dBc on 6M
   - Carrier and Opposite Sideband Suppression: Better than -80dBc
   - Transverter IF Output: 0db to 15dB



IOs:

   - RCA Line In, Line Out, PTT in, PTT Out
   - DB9 Seven Software configurable Open Collector Outputs
   - BNC XVTR TX Out, 10Mhz Reference Input
   - 6.25mm Barrel Mic, CW Key, Headphones and Speaker Outputs
   - SMA PureSignal (Predistortion) Loop Input and Output
   - RJ45 Ethernet LAN Connector
-------------- próxima parte ----------
Um anexo em HTML foi limpo...
URL: http://radio-amador.net/pipermail/cluster/attachments/20161212/4a11bbf1/attachment.htm